GAS SAFETY SHUT-OFF SOLENOID VALVE (The Manual Reset-Normally Open Type)
관련링크
본문
HGSO 2015 / 2025 / 2040 / 2050
HGSO 2050F / 2065F / 2080F / 2100F / 2150F / 2200F
|
HGSO 2015
| HGSO 2025 |
HGSO 2040 / 2050 |
|
HGSO 2050F
| |
HGSO 2065F / 2080F / 2100F / 2150F |
|
HGSO 2200F | |
DIMENSION & TECHNICAL SPECIFICATION
- The Manual Reset - Normally Closed Type -
MODEL |
Overall (mm) |
Weight(KG) |
Connection |
||||
A |
B |
C |
D |
H |
|||
HGSO 2015 (15A) |
56 |
32 |
88 |
104 |
- |
0.87 |
Rp 1/2" |
HGSO 2025 (25A) |
56 |
32 |
88 |
104 |
- |
1.08 |
Rp 1" |
HGSO 2040 (40A) |
160 |
140 |
146 |
229 |
- |
4.00 |
Rp 1" 1/2 |
HGSO 2050 (50A) |
160 |
140 |
157 |
240 |
- |
5.00 |
Rp 2" |
HGSO 2050F (50A) |
215 |
166 |
146 |
240 |
4x17 |
5.00 |
DN 50 |
HGSO 2065F (65A) |
313 |
200 |
259 |
356 |
8x18 |
14.70 |
DN 65 |
HGSO 2180F (80A) |
313 |
200 |
259 |
356 |
8x18 |
15.70 |
DN 80 |
HGSO 2100F (100A) |
316 |
222 |
288 |
397 |
8x18 |
16.60 |
DN 100 |
HGSO 2150F (150A) |
491 |
323 |
326 |
470 |
8x22 |
30.00 |
DN 150 |
HGSO 2200F (200A) |
600 |
340 |
420 |
- |
12x23 |
59.80 |
DN 200 |
GENERAL SPECIFICATION
Working gas | LNG(Town gas), LPG, Air, Flue gas, Non-aggressive gas |
Working voltage | AC 220V |
Ambient temperature | -15 ∼ 60 ℃ |
Max. superficial temperature: | 80 ℃ |
Max. Operating Pressure | 500 mbar |
Voltage tolerance | -15 ~ 10% |
Closing time | < 1 second |
Protection grade | IP 54 5- Dust protected 4- Protection against splashing water |
MATERIALS
Housing base | Aluminium diecast, Brass |
Coil housing | Iron |
Coil | enameled copper wires |
Disk sheet | HNBR |
Core | Pure Iron |
■ TECHNICAL DESCRIPTION
- HGSO series solenoid valve connected to the gas leak detector or alarm signals for the presence of
carbon monoxide, is suitable to perform locking operations on the gas line.
- While electricity is not flowing, the gas passage is opened by pulling manually reset.
- Because of an electrical signal from a gas leak detector, current flows in the coil and
the coil pull a support of shutter to block the flow of gas.
- The supports is removed, the shutter close the gas passage quickly. (within 1 second)
- If energizing of the sensor persists bacause of the presence of gas,
the valve remains under power and does not allow reset.
- When the cause for locking have been eliminated, valve must be opened manually
- HGS series is normally installed downstream a manual shut-off valve and upstream of the gas regulating train.
■ ATTENTION
All installation/maintenance work must be carried out by skilled staff.
Always check that the system is gas-tight after installation.
Failure to follow this manual can result in dangerous situations or damage to the product.
■ INSTALLATION
1. Warning
- For proper and safe operation and long service life of the valve, consider the following recommendations
of the valve during the design of the system when the valve is installed.
· Rated voltage and current
· The degree of protection vessel
· Dimensions of tolerance parallel thread
· Attachment Method
· The environment
· Pull method
· Location inlet section
· Using leased lines
· Max. Operating Pressure
- Shut off the air/gas supply at the main manual shut-off valve and disconnect electrical power to the valve
before proceeding with installation or servicing.
- Before installation, ake sure that the pipeline is free from impurities and vibration-free.
- Solenoid surface may be hot. Do not touch it with bare hands.
- The filter must be installed upstream of the solenoid valve for proper operation.
- Avoid excessive quantities of sealing agent which could enter in the valve.
- Use proper tools only and avoid overtightening.
- Make sure all gaskets are used properly.
- Please be sure protective measures to prevent easy access to the facilities.
- If you do not use the Rated voltage products can cause serious malfunction.
- After installation, function and leaking tests must be carried out.
- Perform maintenance must be done at least once a year.
2. Installation Location
- Ensure that installing area is protected from rain or moisture and sunlight.
- It may cause the heat to the coil according to the installation environment.
Don’t install the valve in a position close to the wall or another device.
■ Standards and specifications of this product are subject to change without prior notice for improved performance.